Daisy powerline 990 repair manual - daigaku Daisy Powerline 990 Repair Manual is a photo app that lets you share your panoramic photos. Title: Daisy Manufacturing Co. Air Rifle, Model 990, Compliance File RP990127 P art II Subject: Daisy Manufacturing Co. Air Rifle, Model 990 Keywords. 887-888 - gold medalist user manual daisy 717 parts model m 853c daisy 008 daisy 22-sg daisy 693 daisy 901 daisy 953 daisy buch air rifle 4841 grizzly red ryder daisy 74 co2 bb gun daisy 5880 shaddow kit avanti 717 triumph.
- Read Free Daisy Dual Power 990 Manual Daisy Powerline 990 Owners Manual - parentchildbond.com Daisy Powerline Pistols provide the ultimate in marksmanship training and backyard plinking fun. With both CO2-powered and spring air powered versions, these air pistols include traditional safety features and realistic actions. Daisy Powerline Pistols are.
- Here you have a total of 4 urethane o-rings that will be needed for your repair on your Daisy Powerline 990 Dual Power Co2 / Pump BB/Pellet gun. Powerline Rifles Archives - Daisy Daisy Red Ryder, Powerline 880, Model 25 Pumpthe diminutive Buck – we make the most legendary BB guns and pellet rifles in the world.
- Vintage DAISY Powerline Model No. 990 Pump Co2 BB Gun Rifle Parts or Repair. 9 product ratings - Daisy Powerline 990 922 822 880 Foam Pump Oil.
HOW TO OPERATE
CAUTION:
Be sure gun is always pointed in a safe
direction
Step 1. OPEN BOLT
Step 2. PUT “ON” TRIGGER SAFETY
Step 3. PUMP
Step 4. LOAD
Step 5. CLOSE BOLT
Step 6. AIM AT SAFE TARGET
Step 7. TAKE “OFF” TRIGGER SAFETY
Step 8. FIRE
Step 1. OPEN BOLT
Pull straight back on bolt handle, pulling it fully to the rear
(See Drawing No. 1A). The gun cannot fire with bolt open.
Step 2. PUT “ON” TRIGGER SAFETY
The bolt must FIRST be opened, then the trigger safety is
pushed from the left to right so that NO red is showing (See
Drawing No. 1B).
CAUTION:
Gun must always be pointed in a safe
direction.
BOLT HANDLE
LOADING PORT
TRIGGER
SAFETY
NO. 1B
TRIGGER SAFETY ON
TRIGGER SAFETY OFF
red showing on opposite side
NO. 1A
Step 3. PUMP
The bolt must be opened to pump gun. For greater safety,
we recommend that the bolt remain open while pumping and
that you close the bolt only when the barrel can be pointed in
a safe direction. With the muzzle pointed in a safe direction,
pump the gun the desired number of times up to 10. More
power means greater chance of serious injury. Never put fin-
ger on trigger until ready to fire the gun. NOTE: Do not pump
your gun more than 10 times. Muzzle energy increases pro-
duced by more than 10 pumps are minor, and increased
pumping will damage your gun.
CAUTION:
Be sure to grasp pump handle firmly as
you close the lever to prevent it from snapping back and
causing possible injury. Also be careful to keep fingers out of
cocking mechanism when closing lever. (See “PINCH
POINTS,” Drawing No. 2).
WARNING:
Do not open the bolt, close the bolt, and
then pull the trigger before pumping. This procedure can result
in a loaded gun and a projectile being expelled from the gun
during pumping. Recock the gun by opening the bolt and put
“on” trigger safety before pumping as in Steps 1 and 2.
PULL LEVER OUTWARD
FOR FULL STROKE
THEN RETURN
PINCH
POINTS
NO. 2
Filling the BB magazine for the PowerLine® 880, 880S, 1880:
The loading door is located on the left side of receiver (See
Drawing No. 3). Push door down and fill magazine with
approximately 50 BBs. Do not overfill or the feed system may
not operate properly.
Step 4. LOAD (PowerLine
®
880, 880S, 1880)
LOADING BBs: With the bolt handle back and BBs in the
magazine (See “BB MAGAZINE” section), RAISE the muzzle of
the gun 45 degrees to 90 degrees. When raising the muzzle,
be sure the front sight is pointed upward since the gun may
not feed properly if it is on its side (See Drawing No. 4A). A
BB can be seen on the magnetic tip by looking into the load-
ing port (See Drawing No. 4A). If a BB does not feed onto the
magnetic tip when the muzzle is raised, shake the gun slightly.
Push bolt handle fully forward and the BB is in firing position.
Be sure the front sight is pointed upward when raising the
muzzle to insure proper feeding.
CAUTION:
Always view the BB or Pellet when closing
the bolt and loading port.
WARNING:
BBs feed from the magazine by gravity
which requires that the muzzle be raised. NEVER ASSUME
THE MAGAZINE OR CHAMBER IS EMPTY even if the gun
does not fire a projectile.
LOADING PELLETS: With the bolt back and BBs removed
from the magazine (See “TO EMPTY MAGAZINE,” Page 7),
advance the bolt forward until the magnetic tip is visibly even
with the rear edge of the pellet loading port; lower the muzzle
and load a pellet, solid end forward (See Drawing No. 5). Push
the bolt handle fully forward and the pellet is chambered in
the firing position.
IMPORTANT: Do not allow a pellet to fall into the rear of the
loading port and become jammed in the BB feed hole. If this
occurs, have a qualified gunsmith remove the left receiver and
clear the loading port or return gun to Daisy.
IMPORTANT: Care must be exercised when shooting pel-
lets while the magazine contains BBs. Loading a BB and pel-
let at the same time may result in a jammed or obstructed
barrel.
RIGHT
WRONG
NO. 3
NO. 4A
LOADING HOLE
LOADING DOOR
PUSH DOOR
DOWN TO OPEN
BB MAGAZINE
NO. 4B
Daisy Powerline 990 Parts
BB
LOADING
PORT
MAGNETIC
TIP
Step 4. LOAD (PowerLine
®
22X, 22SGT, 22S)
LOADING PELLETS: With the bolt back lower the muzzle
and load a pellet, solid end forward (See Drawing No. 5). Push
the bolt handle fully forward and the pellet is chambered in
the firing position.
NO. 5
LOADING PORT
PELLET
(SOLID
END FORWARD)
MAGNETIC
TIP
4
5