Whirlpool Range / Stove / Oven Fault Codes: Failure Code: Fault Code Description: Solution: 4 Digit Failure Codes (for 2 digit codes see below) F1 - E0: EEPROM communication error: 1. Disconnect power for at least 30 seconds. Re-apply power and observe for at least one minute. If code re-appears, replace control board (also called ERC. The oven door switch detects whether the oven door is closed and helps control the oven light. Replace the switch if it doesn’t control the oven light properly. 0x80192f76 seems to indicate that the connectivity with credential occurs some issue. For such kind of issue, we may need to collect deeper logs or traces to analysis, I would recommend to create an online support ticket. The F0 code displays if there are no previous fault codes and you hold the CANCEL key for 5 seconds. Press CANCEL to clear the display.

1. F8e0 Error Code Whirlpool Range
2. F8e0 Error Code Whirlpool Gas Range
3. F8e0 Error Code Microwave

JENN-AIR, MAYTAG, MAGIC CHEF - LARGE CAVITY RANGES AND 'D' SERIES WALL OVENS MODEL YEAR(S): 2003 AND NEWER

FAULT CODE DESCRIPTION

Each fault code consists of four (4) digits. The function of each digit is described in Table 1 below.

Table 1: Fault Code Description

Fault Code, Problem, Component(s) to Check

1C1C Shorted Key................................................................... Check wire harness connector and ensure proper connection and wires show continuity. If ok, replace control.

1C2C Keyboard tail disconnected ...........................................(single cavity or upper oven) Check wire harness connector and ensure proper connection and wires show continuity. If ok, replace control.

1C31 Cancel key circuit (single cavity or upper oven) ............ Replace control.

1C32 Cancel key circuit (lower oven)....................................... Replace control.

1C4C Micro communication failure.......................................... Replace control.

1C6C EEPROM error hardware fault......................................... Replace control.

1C7C Control not calibrated .................................................... Replace control.

1C8C User-option CRC error in EEPROM.................................. Replace control.

1C81 CRC cook profile error (single cavity or upper oven) ..... Replace control.

1C82 CRC cook profile (lower oven)........................................ Replace control.

1D11 Temperature above 600° F and door unlocked.............(single cavity or upper oven) Ohm oven sensor and harness. Verify proper connection. If ok, replace control.

1D12 Temperature above 600° F and door unlocked.............(lower oven) Ohm oven sensor and harness. Verify proper connection. If ok, replace control.

1D21 Temperature above 950° F and door locked .................(single cavity or upper oven) Ohm oven sensor and harness. Verify proper connection. If ok, replace control.

1D22 Temperature above 950° F and door locked .................(lower oven) Ohm oven sensor and harness. Verify proper connection. If ok, replace control.

3D11 Sensor open ..................................................................(single oven or upper oven) Ohm oven sensor and harness. Verify proper connection.

3D12 Sensor open ..................................................................(lower oven) Ohm oven sensor and harness. Verify proper connection.

3D21 Sensor shorted ..............................................................(single cavity or upper oven) Ohm oven sensor and harness. Verify proper connection.

3D22 Sensor shorted ..............................................................(lower oven) Ohm oven sensor and harness. Verify proper connection.

3D41 Meat probe shorted........................................................(single cavity or upper oven) Ohm meat probe and check for shorted harness. If ok, replace control.

3D51 Meat probe not calibrated ..............................................(single cavity or upper oven) Replace control.

4D11 Door switch position error, opened when latch locked ..(single cavity or upper oven) Check door switch and ohm door switch wiring.

4D12 Door switch position error, opened when latch locked ..(lower oven) Check door switch and ohm door switch wiring.

4D21 No/low cooling fan rotation (no RPM)............................(single cavity or upper oven) Check connection at cooling fan. If ok, replace blower. DO NOT REPLACE CONTROL.

4D22 No/low cooling fan rotation (no RPM)............................(lower oven) Check connection at cooling fan. If ok, replace blower. DO NOT REPLACE CONTROL.

4D31 Cooling fan state error (states on when fan off) ............(single cavity or upper oven) Check all fan connections. If ok, replace control.

4D32 Cooling fan state error (states on when fan off) ............(lower oven) Check all fan connections. If ok, replace control.

4D41 Cooling fan rotation over speed.....................................(single cavity or upper oven) Check all fan connections and check for airflow restrictions. If ok, replace cooling fan.

4D42 Cooling fan rotation over speed.....................................(lower oven) Check all fan connections and check for airflow restrictions. If ok, replace cooling fan.

4D51 Door switch circuit failure...............................................(single cavity or upper oven) Check connections and wiring.

4D52 Door switch failure (lower oven) .................................... Check connections and wiring.

9D11 Latch will not lock...........................................................(single cavity or upper oven) Check door lock connections. If ok, replace door lock assembly.

9D12 Latch will not lock...........................................................(lower oven) Check door lock connections. If ok, replace door lock assembly.

F8e0 Error Code Whirlpool Range

9D21 Latch will not unlock.......................................................(single cavity or upper oven) Check door lock connections. If ok, replace door lock assembly.

F8e0 Error Code Whirlpool Gas Range

9D22 Latch will not unlock.......................................................(lower oven) Check door lock connections. If ok, replace door lock assembly.

9D31 Latch both locked and unlocked ....................................(single cavity or upper oven) Check door lock connections. If ok, replace door lock assembly.

9D32 Latch both locked and unlocked ....................................(lower oven) Check door lock connections. If ok, replace door lock assembly.

Duet Washer Error / Fault Codes

Once you are in the Duet Washer's Diagnostic Mode momentarily press the 3rd button you used to enter diagnostics, and the washer will display the last 4 fault codes one button press at a time. There are a few helpful things to note here. If the Duet successfully runs 10 cycles in a row with no fault the error will be cleared from the washer's memory, so any errors you see are likely new and active.
After you have recorded any stored errors you can clear the code by pressing and holding the 3rd diagnostics button for 5 seconds. If there are no stored errors 888 will be displayed with 3 beeps.

Duet Washer error and fault codes are displayed by alternating F#__ and E#__ The F error describes the washer system and the E error further defines the washer part that may be having a problem. F1, F2, F6 Are main control and program faults. F3 faults are washer sensor related problems. F5 faults are door lock and door switch related duet codes. F7 Faults are motor and motor control related problems. F8 Faults are water related… valve, dispensing system, water level, steam valve, and flow meter problems. Lastly F9 faults are related to the washer's ability to drain.

NOTE: 'Anytime I say unplug and check connections' or something like that...
It also means unplug the washer so you don't get electrocuted!

SUDS Error - Suds fault.

• Your Duet washer has detected that it is full of soap suds which are difficult to drain. Or perhaps your Duet washer wants a beer… This can be caused by using non HE washer detergent, using too much soap, or possibly a drain pump or pressure sensing problem.

F0E1 Error - Load detected during a clean cycle fault.

• Your Duet washer has detected a load during a washer cleaning cycle. If this does not appear to be the case you may have mechanical friction causing drag when the inner washer drum is rotating.

F1E1 Error - Main control fault.

• This is a bad one… Duet washer main control error. Try unplugging the washer for a minute and putting the washer through a quick diagnostic test and see what you get… In some cases this can reset the control and buy you some time.

F1E2 Error - Motor control fault.

• The motor control board (MCU) has attempted to reset several times and does not like the result. (Duet Washer Motor Tests)

F2E3 Error - Cycle fault.

• This is a rare one but it means that something is wrong with the washer cycle that was selected. Put your Duet washer through the UI Tests, and check all of the connections to the control. your washer may need a new main control board.

F3E1 Error - Pressure switch/ sensor fault.

• Check the pressure sensing hose for kinks or blockage. You will also want to check the pressure sensor (Duet Washer Pressure Sensor Check)

F3E2 Error - Temperature sensor fault.

• This error will display if the washer's temperature sensor is out of range. (23º - 217º) check all wire connections from control to the washer temp sensor. I have had several of these become unplugged at the sensor connection at the back of the washer drum. (Duet Washer Temperature Sensor Check)

F5E1 Error - Door switch fault.

• Possible causes…
  1. Your Duet washer has a bad door switch.
  2. You have not opened to door for 3 wash cycles… (Too many Margarita!?)
  3. Trying to start a cycle when the washer door is open. (Duet Washer Door Switch Check)

F5E2 Error - Door lock fault.

• Your Duet washer was not able to lock the door after 6 times… you can't say it didn't try. Check that the tab on the washer's door that inserts into the door lock is not broken, that it's properly aligned with the door lock hole, and that there is nothing that may be jamming the lock. (Duet Washer Door Lock Check)

F5E3 Error - Door unlock fault.

• Your Duet washer was not able to unlock after 6 tries. Check that the tab on the washer's door that inserts into the door lock is not broken, that it's properly aligned with the door lock hole, and that there is nothing that may be jamming the lock.

F6E2 Error - Communication fault.

• Communication error between the main control and the motor control. Check all the wire connections from the CCU to the MSU for good connection. If everything looks good, check for broken wires with a multi meter.

F6E2 and F6E3 Errors - Communication fault

• Communication fault between the main control board (CCU) and the user interface (UI) unplug and check the wire connections between the washer's (CCU) and the washer's (UI)

F7E2 Error - Motor or motor control board fault.

• Make sure the inner drum turns freely. (There may be some magnetic resistance (Magnetic Motor) but there should be no mechanical drag.)) (Duet Washer Motor Check)

F8E0 Error - (Steam models) Steam valve fault.

• Check that water is getting to the steam valve, it may be blocked or restricted.

F8E1 Error - Water fill fault.

• Your Duet washer has tried to fill for 13 minutes but has not sensed any water entering the tub… Are your home valves turned on? Is the drain hose too far down the drain pipe? If the end of the drain hose is below the water level in the washer, water can siphon out as fast as it goes in. Check water valve electrical connections before changing out the valve.

F8E2 Error Dispenser fault.

• This means that the dispenser motor which directs fill water to the appropriate dispenser area, is not moving properly. take the top off and run the Duet Washer Quick Diagnostic Test, C03 checks the Duet washer's dispensing system.

F8E3 Error - Overflow fault.

• If this was real you are probably already aware of it… but hopefully your Duet washer's computer brain saved the day and drained the water out before your floor was ruined. If you get this error...
  1. check that the washer's water valves are closing all the way and water is not filling into the tub when it shouldn't be. If water is slowly filling the tub even when the washer is unplugged you need to replace the washer fill valves. If it's filling quickly and it suddenly stops when you unplug the washer you may have a bad main control board.
  2. Check that the drain pump is working properly.
  3. Check the pressure sensor.

F8E4 Error - Flow meter fault.

• Not even 0.1 L of water has entered the tub from the first 30 seconds of the Duet Washer Quick Test… Is the water turned on?

F9E1 Error - Long drain fault.

• This is the most common Duet washer error code! The F9E1 long drain error is referring to duration not length. if it takes longer than 8 minutes to drain your highly water efficient washer then ether the drain system is pugged up with who knows what or the drain pump is having a problem. The best way I have found to deal with the water when your washer's drain pump isn't working is to use a shop vac and pull from the drain hose. If that works the your pump is highly suspect. If it doesn't work then you almost certainly have a clog in your Duet washer's drain system and the pump may be fine.

Clear Stored Duet Error & Fault Codes

F8e0 Error Code Microwave

Not all washer made by Whirlpool have the ability to clear error code memory. Thankfully this style does... Once you are in the Duet washer's diagnostic mode and have recorded any errors that the washer has in it's little computer brain, press and hold the 3rd button used to enter diagnostics for 5 seconds... Like it never happened : )